Pass the line through the eye of your tackle at least twice, leaving 12" for your knot.
Loop the tag end around the standing line, then pass the tag end through your loop 8 to 10 more times.
Pull the tag end to tighten the knot, making sure the 8-10 wraps snug down neatly.
Pull the standing line to jam the knot against your tackle eye, then trim the tag end.
Uni to Uni Splice Knot
For tying PowerPro to mono of similar diameter
Lay PowerPro and monofilament parallel, with 12" to 18" tag ends facing opposite directions.
Loop the tag end of the mono around both lines, then pass the tag end through your loop 5 to 6 more times. Pull the tag end through your loop 5 to 6 more times. Pull the tag end to tighten the knot, making sure the wraps snug down neatly.
Repeat step #2 using the PowerPro tag end, but use 8 to 10 wraps.
Pull on the standing lines to jam the two knots together tightly.
Trim the PowerPro tag end about
Reverse Knot
For tying PowerPro to mono of larger diameter - easy knot
Double your PowerPro, leaving a 1/2" loop at the end. Wrap the PowerPro around the mono 10 to 12 times, leaving your loop open and opposite the mono tag end.
Pass the mono tag end through the PowerPro loop.
Pull on both lines to tighten the knot, jamming the wraps together.
Tie a Lock (see right)
Palomar Knot
For tying terminal tackle - easy knot
Make a 10" loop in the line, then pass it through the eye of your tackle.
If the eye is big enough, pass the loop through a second time.
Tie a simple overhand knot, but don't pull it tight.
Pass your tackle through the loop.
Pull on your standing line to tighten the knot, then trim
Albright Knot
For tying PowerPro to mono of larger diameter - stronger knot
Make a loop in the mono, and hold it with your left hand. Double 30" of PowerPro to create a 15" two-strand section. Pass this through the mono loop.
Wrap the PowerPro loosely around the fingertip of the hand you're using to hold the mono, then wrap the PowerPro around itself and the mono 20 to 25 times. Work toward the end of the loop, keeping your wraps tight and snug.
Run the PowerPro back through the mono loop so it exits on the same side it entered.
Wet the PowerPro, and tug on the standing line and tag end to jam your wraps tightly together, moving them toward the end of the loop.
Pull both standing lines to tighten the knot, then use soft-jawed pliers or a gloved hand to pull the knot tighter. Pull both standing lines at once to make sure the knot is secure.
Tie a Lock.
Lock Knot
To finish the Albright or Reverse Albright
Loop the PowerPro tag end around the standing PowerPro, then pass the tag end through this loop three times.
Pull the tag end to tighten the wraps, then trim your tag ends.
No-Name Knot
For tying PowerPro to Fluorocarbon/Mono shock leader
Make figure 8 loop on leader
Insert PowerPro into figure 9 loop
Wrap PowerPro 12 times and 12 times back to the other direction
Insert PowerPro back into figure 8 loop
Cinch leader tightly
Pull main PowerPro slowly then pull PowerPro tag-end slowly and pull both main and tag-end of PowerPro tightly
Make a half hitch twice on tag-end
Cut the tag-end of PowerPro and leader
Wind-On Leader Knot
For Loop to Loop connection between PowerPro to Shimano Wind-On Leader
Make Bimini-twist on PowerPro main line
Pass loop on Wind-On Leader through loop of PowerPro
Hold both main line loop and wind-on loop by two fingers, pass end of Wind-On through the main line loop. Pass end of wind-on through the main line loop again
Repeat this 2-3 times
Slowly pull both lines by making even lengths and cinch to complete